Skip to main content

Small Scale Track - Tyler - March 27

This week the team sorted through aluminum bar specs to see what series of aluminum we should be using.  Below is our in progress spreadsheet listing the vendors we've been looking at.
Spartan Superway Small Scale Aluminum Sourcing







Vendor Checked
Type of Aluminum Available
Our dimensions of 1/4" thick, 1" wide, 4ft long available?
Yield Str
Hardness
COST
NOTES
MCMASTER CARR6061NO. 1/4"x1" in 3' or 6'35,00095$7.70 EA for 3' $13.51 for 6'
3003 Series has a 40% lower yield strength and a 58% lower Brinell hardness. Much easier to bend.
MCMASTER CARR3003NO. 1/4"x1" in 3' or 6'21,00040$60.59 for 3' $108.19 for 6'
MCMASTER CARR6063YES21,00060$12.65 for 4' $19.16 for 8'-
MCMASTER CARR1100NO. 1/4"x1" in 3' or 6'15,00030$10.00 for 3' $17.25 for 8'Maybe buy this in 8' and cut in half
MIDWEST STEEL SUPPLY6061YES35,00095$10.56 EAOne of last years' vendors
METAL WERXPERMANENTLY CLOSED----One of last years' vendors
GORILLA METALS - SANTA CLARAPERMANENTLY CLOSED----One of last years' vendors
GORILLA METALS - HAYWARDPERMANENTLY CLOSED----One of last years' vendors
HOME DEPOT ONLINEDoes not say, assume low-qual 6061NO. 1/4"x1"x8'35,00095$24.98 EA3 in stock in store in Santa Clara
TCI ALUMINUM - HAYWARD6061NO. 1/4"x1"x12'35,00095Does not list on website-
RYERSON6061NO. 1/4"x1"x12'35,00095Scales on amount bought, expensive.-
COAST ALUMINUM6061NO. 1/4"x1"x12'35,00095Does not list on website
If another vendor is not found, we can reach out to these guys and see if they will sponsor.
COAST ALUMINUM6063NO. 1/4"x1"x16'21,00060Does not list on website

 
 
 
 
 
 
This is a chart showing the yield strength of different series of aluminum.  We are using it to find a softer aluminum series for our project.






Above is

Comments

Popular posts from this blog

Small Scale Track - Tyler - May 1

This week we obtained all of the rails to be bent and started into the full swing of manufacturing our new curved sections.  We have found out how to consistently get bends in our rails using a step by step process.  We are following last years advice and having only one person (me) manufacture the rails so that there is not measurement bias or manufacturing differences between users of the track bender.  We have begun receiving 3D printer samples from makerspace and found out that they are having great difficulties in getting us our orders, so we will need to revisit this.

Small Scale Track - Tyler - April 10

This week was the start of the 2nd presentation.  The presentations had to be cut short because of the move of the guide way from campus to the 115 Terraine St location.  The remainder of the class was spent purchasing our final materials and setting up reimbursements with Tinan.  We believe we have everything we need ordered.  Also, I found a family friend that can provide access to basic welding equipment!  Hopefully it will be enough for us to complete what we need to.

Small Scale Track - Tyler - September 26

Today was a presentation day for Spartan Superway.  Our presentation talked about our plan to fill the empty space in the middle of the track by adding a T-Junction with a docking station in the middle.  At the docking station, charging of the bogey's would happen.  We also discussed issues with the track bender and recieved valuable feedback on how we could improve both the track bender and the track itself. We also found information about how we could potentially sand cast or injection mold our brackets holding two pieces of the track together.